Low Pass Filter (About Time!!!)

Using a kitsandparts.com kit - and my own wire - I constructed a 20m low pass filter with the clear intention of putting my radio on the air. 

The insertion loss was not nearly as high as I had expected - a good thing in my case.   The insertion loss was about 0.70dB around 14.3MHz, while the attenuation at 28MHz was over 50dB. 

TOO MANY INPUTS!!!!

I woke up this morning with my head spinning.  (No, I didn't get drunk last night).

I had a long discussion last night with a fellow VWS member about radio designs and trying to get a kit together as if I had already volunteered.   I was so tired, I did not have the defense to argue.  He had a lot of good ideas, but he was pushing me to do his design as if it were my own.

I really need to draw the line on that.  I am not willing to take on any new designs beyond my own right now.  I got a lot of good ideas, but that is why my design is stuck!   If a website could feel, I feel like a website that is being overloaded with requests for information and data uploads.

I don't mean to sound ungrateful, but I really need to hit the brakes on volunteering for any kit building designs until I get mine working.  I do not have enough time to do any more. 

Sorry to my friends at VWS.

Updated DDS-60 controller coming. Working on a EIM377 DDS controller.

Just got a nice email from Far Circuits...they are sending me samples of an updated PCB design for interfacing the AMQRP DDS-60 with a PICAXE 28x2 in an RF-friendly PCB.  I had to open up some holes and fix some ground clearances.  They had to fix some off-center etching issues from the previous design.  If these work out, I will definitely send them an order for a full etch of boards in the hope to make a few of them. 

My next big project on the DDS front is an RF-friendly interface for the EIM377 DDS controller.  For the un-informed, the EIM377 is one of the AD9850-based DDS oscillators that have been selling for prices as cheap as $5 to $10.  I bought four of them to play with.  As my previous entry indicates, I was able to interface the EIM377 with the PICAXE 28x2.  I did add a encoder interface to demo at the VWS club meeting, but it was taken apart again for a new mechanical layout.

I will forward new photos as the units are coming in for construction.

"e-Bay" DDS Oscillator

Sorry for the long delay...been working on other things lately.  Riding my bike, playing with my new FT817...

Now, I have started to get back into it again.  My newest challenge...running the PICAXE on 3.3V yet running the display at 5V.   Actually - that turned out to be less of a challenge than I feared.  It seems that the 5V LCD Display works just nicely with the 3.3V input as long as you current limit the interface, which I have done.

With that, I have constructed another AXE401 shield which is connected to an AD9850-based DDS oscillator which has proliferated on eBay for almost a year.  I bought 4 of them for $5 each - and the postage cost as much as the boards.  In spite of that, I still came out ahead.

The reason for the urgency of the 3.3V - the 125MHz reference oscillator is a 3.3V oscillator, so I had to turn down the voltage. 



It does work, though it is harmonic rich.  May have picked the wrong output...two are square-wave, one is unfiltered sine wave, and one is filtered sine wave. 


Better quality photos soon to be coming later.   Hoping to have this ready to show at the "Solder-something" meeting of Vienna Wireless Society on the 4th Friday of July.

Wish I could reveal more, but...

As some of you have been following my blog, I was warned by Jack (AI4SV) that I should not reveal TOO much about my oscillator before I submit my design for publication in QST and QEX.  As a result, I will likely only show photos - no schematics of the work that has been done and no PICAXE programs.  Sorry for the inconvenience this may cause.  

I know there are some on the PICAXE Forum that are clamoring for how I can program a DDS using a PICAXE as there is nothing published.   I can assure you that I have successfully programmed both the DDS-60 oscillator and the AD9834-based FCC-2 kit using my interface(albeit with significant noise margin issues).  This whole effort started because of the sad reality that the FCC-2 PIC-chip program design died with the passing of the FCC-1/FCC-2 designer.  

While I am at Dayton, I am planning to speak with Hendricks Kits about resuscitating the FCC-2 kit as a standalone DDS oscillator, much as the DDS-60 is used.

In any event - I promise that this publication WILL happen - either through QST/QEX, through another QRP group, or this blog.   Preferably ALL of them.

PCB - Power Amplifier

Figure 4-1:  First Prototype - IRF510 Power Amplifier

 

As figure 4-1 above shows, the previous design had the FET laid down with the PCB mounted to the heat sink. It was good for a quick prototype, but is not necessarily the most efficient approach.

 

Figure 4-2:  Updated Power Amplifier Layout

 

 

I looked into a different layout where the FET itself was on the heatsink, while the board it mounted on standoffs at right angles as shown in figure 4-2.  At the same time that I sent in the updated DDS interface, I also sent in this Power Amplifier as well. 

 

Once I get the amplifier design finished, I will be publishing the schematic for the power amplifier - hopefully in QST or QEX - along with the PICAXE interface design.  At very least, VWS will get the design for one of their tech journals when it comes out.  Figures 4-3 through 4-6 show the broadband sweep of the amplifier.

 

 

 

 

 

 

2nd DDS Oscillator Interface Prototype

The second prototype chassis was a more RF-friendly design where the PICAXE is on its own board with very short traces for the CS (Chip Select),  SPI Clock, and SPI Data between the 28x2 and the socket used to hold the DDS-60.

Figure 3-1:  Rev0 PCB with DDS-60 installed.

Figure 3-2:  Front Panel of 2nd Chassis Oscillator

Figure 3-3:  Top View of DDS Oscillator/Interface

The updated version of the interface has four buttons instead of two.  The Blue and Black buttons are the cursor movement buttons like the previous version, but the Green and Red buttons perform band shifts from 80m>40m>...>10m (Green) and 10m>12m>...>80m (Red).

I laid out the circuit and PCB using Express PCB and had it etched by Far Circuits.  The price was right, but there were some alignment issues between top and bottom side that need to be corrected on the next go around.   I will show the board to them when I visit them at Dayton this year.